Aquatec Pressure Switch 100 psi shut off 3/8″ tubing TSO 6800 8800 pump PSW-3100
Aquatec Pressure Switch + Quick Connect Electrical Wire Plugs (made in USA). Typical application is installed on a RO reverse osmosis water system. We also carry many other variation of the Aquatec pressure switches.
Aquatec Pressure Switch 60 psi shut off 3/8″ tubing TSO 6800 8800 pump PSW-360
Aquatec Pressure Switch + Quick Connect Electrical Wire Plugs (made in USA) Brand: Aquatec (Genuine Aquatec Products) Model: PSW-360 (60 psi cut off, 3/8″ inlet/outlet) This pressure switch is used to control the on/off of the Aquatec booster pump 6800 series and 8800 series. Typical application is installed in a RO reverse osmosis water system. Instruction is included with the purchase. This pressure switch comes with quick connect wire plugs that connect quickly to Aquatec booster pump and Aquatec transformer. This switch has 3/8″ inlet and outlet quick connect fitting. All you need to do is push in a 3/8″ OD tubing into the inlet and outlet all the way in, the fitting will seal itself. To remove the tubing, you just need to push the plastic ring firmly agaist the fitting then you can pull out the tubing. Pressure Setting: It is pre-set at 60 psi cut-off pressure, but it is adjustable. The adjustable range is 50 to 90 psi Operation: When the pressure switch is connected to a Aquatec pump and Aquatec transformer, it will turn on the pump when pressure switch is sensing below 60 psi, then it will turn off the pump when the pressure is sensing 60 psi or above. We also carry many other variation of the Aquatec pressure switches. Aquatec # Preset Cut-Off Adjustable Range Inlet/Outlet eBay item # PSW-240 40 psi 30 to 60 psi 1/4″ PSW-340 40 psi 30 to 60 psi 3/8″ PSW-260 60 psi 50 to 90 psi 1/4″ PSW-360 60 psi 50 to 90 psi 3/8″ this listing PSW-280 80 psi 70 to 110 psi 1/4″ PSW-380 80 psi 70 to 110 psi 3/8″ PSW-2100 100 psi 90 to 150 psi 1/4″ PSW-3100 100 psi 90 to 150 psi 3/8″ Technical Specification: Wetted Materials: Nylon, Santoprene, Nitrile Switch Rating: 250VAC, up to 15 amps, UL recognized NSF/FDA approved material Single pole, Double throw Normally closed
Aquatec Pressure Switch 40 psi shut off 3/8″ tubing TSO 6800 8800 pump PSW-340
Aquatec Pressure Switch + Quick Connect Electrical Wire Plugs (made in USA) Brand: Aquatec (Genuine Aquatec products) Model: PSW-340 This pressure switch is used to control the on/off of the Aquatec booster pump 6800 series and 8800 series. Typical application is installed in a RO reverse osmosis water system. Instruction is included with the purchase. This pressure switch comes with quick connect wire plugs that connect quickly to Aquatec booster pump and Aquatec transformer. This switch has 3/8″ inlet and outlet quick connect fitting. All you need to do is push in a 3/8″ OD tubing into the inlet and outlet all the way in, the fitting will seal itself. To remove the tubing, you just need to push the plastic ring firmly agaist the fitting then you can pull out the tubing. Pressure Setting: It is pre-set at 40 psi cut-off pressure, but it is adjustable. The adjustable range is 30 to 60 psi Operation: When the pressure switch is connected to a Aquatec pump and Aquatec transformer, it will turn on the pump when pressure switch is sensing below 40 psi, then it will turn off the pump when the pressure is sensing 40 psi or above. We also carry many other variation of the Aquatec pressure switches. Aquatec # Preset cut-off Adjustable Range Inlet/Outlet eBay item # PSW-240 40 psi 30 to 60 psi 1/4″ PSW-340 40 psi 30 to 60 psi 3/8″ this listing PSW-260 60 psi 50 to 90 psi 1/4″ PSW-360 60 psi 50 to 90 psi 3/8″ PSW-280 80 psi 70 to 110 psi 1/4″ PSW-380 80 psi 70 to 110 psi 3/8″ PSW-2100 100 psi 90 to 150 psi 1/4″ PSW-3100 100 psi 90 to 150 psi 3/8″ Technical specification: Wetted Materials: Nylon, Santoprene, Nitrile Switch Rating: 250VAC, up to 15 amps, UL recognized NSF/FDA approved material Single pole, Double throw Normally Closed
Aquatec Pressure Switch 80 psi shut off 1/4″ tubing TSO 6800 8800 pump PSW-280
Aquatec Pressure Switch TSO + Quick Connect Electrical Wire Plugs (made in USA) Brand: Aquatec (Genuine Aquatec components) Model: PSW-280 (80 psi cut off, 1/4″ inlet/outlet) This pressure switch is used to control the on/off of the Aquatec booster pump 6800 series and 8800 series. Typical application is installed on a RO reverse osmosis water system. Instruction is included inside package. This pressure switch comes with quick connect wire plugs that connect quickly to Aquatec booster pump and Aquatec transformer. This switch has 1/4″ inlet and outlet quick connect fitting. All you need to do is to push in a 1/4″ OD tubing into the inlet and outlet all the way in, the fitting will seal itself. To remove the tubing, you just need to push the plastic ring firmly against the fitting then you can pull out the tubing. Pressure Setting: It is pre-set at 80 psi cut-off pressure, but it is also adjustable. The adjustable range is 70 to 110 psi Operation: When the pressure switch is connected to a Aquatec pump and Aquatec transformer, it will turn on the pump when pressure switch is sensing below 80 psi; then it will turn off the pump when the pressure is sensing 80 psi or above. We also carry many other variation of the Aquatec pressure switches. Aquatec # Preset Cut-off Adjustable Range Inlet/Outlet PSW-240 40 psi 30 to 60 psi 1/4″ PSW-340 40 psi 30 to 60 psi 3/8″ PSW-260 60 psi 50 to 90 psi 1/4″ PSW-360 60 psi 50 to 90 psi 3/8″ PSW-280 80 psi 70 to 110 psi 1/4″ PSW-380 80 psi 70 to 110 psi 3/8″ PSW-2100 100 psi 90 to 150 psi 1/4″ PSW-3100 100 psi 90 to 150 psi 3/8″ Technical Specification: Wetted Materials: Nylon, Santoprene, Nitrile Switch Rating: up to 250VAC, up to 15 amps, UL recognized NSF/FDA approved material Single Pole, Double Throw Normally closed
Aquatec Pressure Switch 80 psi shut off 3/8″ tubing TSO 6800 8800 pump PSW-380
Aquatec Pressure Switch + Quick Connect Electrical Wire Plugs (made in USA) Brand: Aquatec (Genuine Aquatec components) Model: PSW-380 (80 psi cut off, 3/8″ inlet/outlet) This pressure switch is used to control the on/off of the Aquatec booster pump 6800 series and 8800 series. Typical application is installed on a RO reverse osmosis water system. Instruction is included inside package. This pressure switch comes with quick connect wire plugs that connect quickly to Aquatec booster pump and Aquatec transformer. This switch has 3/8″ inlet and outlet quick connect fitting. All you need to do is to push in a 3/8″ OD tubing into the inlet and outlet all the way in, the fitting will seal itself. To remove the tubing, you just need to push the plastic ring firmly against the fitting then you can pull out the tubing. Pressure Setting: It is pre-set at 80 psi cut-off pressure, but it is also adjustable. The adjustable range is 70 to 110 psi Operation: When the pressure switch is connected to a Aquatec pump and Aquatec transformer, it will turn on the pump when pressure switch is sensing below 80 psi; then it will turn off the pump when the pressure is sensing 80 psi or above. We also carry many other variation of the Aquatec pressure switches. Aquatec # Preset Cut-off Adjustable range Inlet/Outlet PSW-240 40 psi 30 to 60 psi 1/4″ PSW-340 40 psi 30 to 60 psi 3/8″ PSW-260 60 psi 50 to 90 psi 1/4″ PSW-360 60 psi 50 to 90 psi 3/8″ PSW-280 80 psi 70 to 110 psi 1/4″ PSW-380 80 psi 70 to 110 psi 3/8″ PSW-2100 100 psi 90 to 150 psi 1/4″ PSW-3100 100 psi 90 to 150 psi 3/8″ Technical specification: Wetted Materials: Nylon, Santoprene, Nitrile Switch Rating: up to 250VAC, up to 15 amps, UL recognized NSF/FDA approved material Single Pole, Double Throw Normally closed
Aquatec Cdp 8800 Water Booster Pump + Transformer 115V Used
The Aquatec 8800.
AQUATEC 115v TRANSFORMER FOR 8800 SERIES BOOSTER PUMPS TACS 114-48
From warehouse liquidation , brand new old stock 24V 2A power units for Aquatec 8800 booster pump.
AQUATEC 8851 RO BOOSTER PUMP 8851-2J03-B421 + TRANSFORMER + 3/8″ PORT SWITCH
WHAT YOU WILL RECEIVE ONE (1) NEW AQUATEC 8851 SERIES RO BOOSTER PUMP WITH 3/8″ JG INSERTS PART NUMBER 8851-2J03-B421INPUT/OUTPUT 3/8″ QUICK CONNECT24 VACONE (1) NEW 8800 TRANSFORMER 115VPART NUMBER: TACS 114-48ONE (1) NEW AQUATEC PRESSURE SWITCH FOR 6800 AND 8800 BOOSTER PUMPS 3/8″ QUICK CONNECTSPART NUMBER: PSW 340MADE IN THE USA CLICK BELOW FOR YOUR WARRANTY AND INSTALLATION INSTRUCTIONS(requires Adobe Reader: it’s free) Get It Fast!! Get a Tracking Number!!For Only $57.00 More, Select USPS Priority Mail at Checkout and Receive Your Item in 2-3 Days and Get a Tracking Number and Up to $50 Insurance Protection.NOTE: USPS does not offer tracking numbers for First Class shipping.WARNING: Domestic USPS packages are not insured unless Priority Mail or Express shipping are purchased. Don’t pay more for less!We ship sooner, faster, and for less than our competitors.We ship immediately.We charge you less than our competitors charge you for slower service.We combine shipping upon request.We will match all verified competitor’s prices.We ship internationally.Service makes the difference! BETTER PUMPS BETTER LIVING PUMP TYPICAL APPLICATIONS Water Treatment/RO Carbonation Systems Misting Systems Alternative Energy/Solar Medical Labwater Laser Cooling Systems Fuel Cells USE AND BENEFITSThis pump is usually used to boost water supply pressure to a Reverse Osmosis water system. If your water supply pressure is below 40psi, you should add this pump to your RO system.This water booster pump is to boost the input water pressure. It is usually used to increase the input water pressure for Reverse Osmosis systems. (boost pressure to 60 to 80 psi).This pump is suitable for RO systems that use up to a 120GPD membrane.For RO systems, an increase in input pressure means an increase in water production and water purityRO systems will run more efficient, with less waste water. Since it uses a pressure switch and solenoid valve to turn on/off the water input, it can turn on and turn off more accurately than the mechanical auto shut-off valve.For large water containers or an open water tank, you can use a float switch or level switch to control the operation of the pump. Product Data Sheet: Aquatec.comWarranty Statement: Aquatec.comInstallation Instructions: Aquatec.com Aquatec’s original product, and still the “global standard” in booster pump technology, providing reliable inlet pressure for efficient membrane utilization.These pumps are capable of continuous duty and are effective for recirculation based applications as well. They are ideally suited to work with hydro-pneumatic storage systems but are compatible with most hydraulic shut-off valves also. These pumps are commonly used with one or more of Aquatec’s flow control components including: pressure switches (PSW Series), tank level controllers (TLC Series) or electronic shut-off valves (ESO Series). FAQ for RO BOOST PUMPS and DELIVERY PUMPS:Q. The R.O. system is not working properlyA. See IMI 147, R.O. Boost Pump Troubleshooting guide: Aquatec.comQ. The CDP, Continuous Duty Pump, runs continuously. A. See IMI 156, Automatic Shut Off Valve’s effect on the PSW’s shut off abilityQ. The pump that delivers water from the holding tank to the refrigerator is noisyA. The pressure switch controlled demand delivery pump is probably delivering morewater than the icemaker can accept (usually about 1/4 gpm at 35 psi), and is momentarilyreaching its shutoff pressure. Use a lower flow pump, and add an accumulator betweenthe pump and refrigerator if necessary. Open the “high voltage drinking water deliverypumps” selection chart, section A, for recommended choices. Q. What effect does feed pressure have on the tank/faucet pressures?A. None. The flow of water to the membrane will increase, but 80 psi pump dischargepressure will not change due to the preset by pass pressure.Q. What effect does higher by-pass pressures have on tank/faucet pressures?A. Since the pressure entering the membrane has increased, so will the pressure exitingthe membrane, at the expense of flow, however. Q. What is the membrane rating based on?A. Based on 95% rejection of TDS levels at 600 ppm and 60 psi membrane feed pressure,in a 70 degree F ambient environment. Q. The boost pump output pressure is only 60psi?A. Assuming you have not adjusted the by pass setting, you may be using a membranewith a permeate production higher than the pump can supply. Either switch to a higherflow pump, or go to a lower rated membrane. Q. Are low feed pressure shut off switches (LPS) available?A. The LPS comes with the appropriate wire harness, but a tee with a 1/8” NPT femalecenter port is not provided. TRANSFORMER Aquatec’s transformers are both current and temperature protected for additional safety protection. Aquatec pump-transformer combinations are designed to operate at maximum efficiency under a wide range of voltage conditions without overheating or overloading. This can save the end-user thousands of kilowatt hours per year compared to less efficient pumps. FeaturesNew Aquatec replacement tranformer for 8800 series booster pumpsDesigned and manufactured by Aquatec to ensure compatibility and proper operationStandard 2-Prong PlugOEM PartSpecificationsInput Voltage: 115-120 VACOutput Voltage Max: 24 VACCord Length: 6 FeetOverload Protection: Thermal Fuse Specification Sheet: Aquatec.com SWITCH Aquatec’s pressure and Vacuum Switches (PSW and VSW Series) provide a full range of in-line pressure sensing electrical switches. These switches, typically mounted near a hydropneumatic holding tank, automatically control the system pump and/or solenoid valve as required. They can also be used to enable hydraulic shut-off valves to operate reliably and positively.Aquatec’s Pressure and Vacuum Switches are normally closed and can be pre-set at various shut-off pressures. If necessary, they can be adapted to operate as normally open switches through minor modifications to the wire terminal connector. The PSW/VSW Series also includes a modular connector for plug-and-play integration with Aquatec’s other system components. FeaturesElectronically shuts off booster pump if feed water is interruptedCompact and inexpensiveHigh Reliability100% factory testedSpecificationsPort Size: 3/8”Pressure: 40PSIVoltage: 250 VAC Specification Sheet: Aquatec.com
AQUATEC RO VARIABLE SPEED PUMP 115VAC 5502-IDN2-V77D
WHAT YOU WILL RECEIVE ONE (1) NEW AQUATEC 5502 SERIES RO VARIABLE SPEED PUMP WITH 1/2″ QUAD PORT PART NUMBER 5502-IDN2-V77DINLET/OUTLET 1/2″ QUAD PORT115 VAC50 PSI0.25-4.5 GPMMADE IN THE USA CLICK BELOW FOR YOUR WARRANTY AND INSTALLATION INSTRUCTIONS(requires Adobe Reader: it’s free) THE MOST POPULAR DELIVERY PUMP ON THE MARKET Get It Fast!! Get a Tracking Number!!For Only $57.00 More, Select USPS Priority Mail at Checkout and Receive Your Item in 2-3 Days and Get a Tracking Number and Up to $50 Insurance Protection.NOTE: USPS does not offer tracking numbers for First Class shipping.WARNING: Domestic USPS packages are not insured unless Priority Mail or Express shipping are purchased. Don’t pay more for less!We ship sooner, faster, and for less than our competitors.We ship immediately.We charge you less than our competitors charge you for slower service.We combine shipping upon request.We will match all verified competitor’s prices.We ship internationally.Service makes the difference! BETTER PUMPS BETTER LIVING TYPICAL APPLICATIONS Beverage/Food Service Alternative Energy/Solar General Industrial Plumbing USE AND BENEFITS The Aquajet Variable Speed Pump provides constant pressure and integrates a state-of-the-art digital controller which maintains constant pressure (within 2 PSI) for variable flow rates throughout their operating ranges. A pressure transducer monitors any pressure changes and adjusts the operating speed accordingly. This pump is capable of sustaining continuous running for approximately 55 minutes. The motor is equipped with an auto reset thermal protector that will shut down the system allowing the components to cool. After approximately 25 minutes, the pump will restart.Great for applications with long lengths of hose or that require variable flow rates such as multiple fixtures drawing fluid from a single source.50 PSI Standard Setting1/2″ Quad Ports3 ChamberFor tubing that runs over 30 feet6 foot line cord Benefits Constant pressure across multiple outletsNo accumulator tanks requiredReduces system bacteriaReduces space requirementsNo pressure switches requiredLess system service requiredPlug-and-play performance Product Data Sheet: Aquatec.comWarranty Statement: Aquatec.comInstallation Instructions: Aquatec.com Copyright, 2009-2024; Discounted Water Filters, Inc, peponlinesales, and all affiliates; All Rights Reserved.
AQUATEC 6800 SERIES RO BOOSTER PUMP 24VAC 6840-2J03-B221 + TRANSFORMER
WHAT YOU WILL RECEIVE ONE (1) NEW AQUATEC 6800 SERIES RO BOOSTER PUMP WITH 1/4″ JG INSERTS PART NUMBER 6840-2J03-B221INPUT/OUTPUT 1/4″ QUICK CONNECT24 VACONE (1) NEW 6800 TRANSFORMER 115VPART NUMBER: TAS 114-19EPMADE IN THE USA CLICK BELOW FOR YOUR WARRANTY AND INSTALLATION INSTRUCTIONS(requires Adobe Reader: it’s free) Get It Fast!! Get a Tracking Number!!For Only $57.00 More, Select USPS Priority Mail at Checkout and Receive Your Item in 2-3 Days and Get a Tracking Number and Up to $50 Insurance Protection.NOTE: USPS does not offer tracking numbers for First Class shipping.WARNING: Domestic USPS packages are not insured unless Priority Mail or Express shipping are purchased. Don’t pay more for less!We ship sooner, faster, and for less than our competitors.We ship immediately.We charge you less than our competitors charge you for slower service.We combine shipping upon request.We will match all verified competitor’s prices.We ship internationally.Service makes the difference! BETTER PUMPS BETTER LIVING PUMP TYPICAL APPLICATIONS Water Treatment/RO Carbonation Systems Misting Systems Alternative Energy/Solar Medical Labwater Laser Cooling Systems Fuel Cells USE AND BENEFITSThis pump is usually used to boost water supply pressure to a Reverse Osmosis water system.If your water supply pressure is below 40psi, you should add this pump to your RO system.This water booster pump is to boost the input water pressure. It is usually used to increase the input water pressure for Reverse Osmosis systems. (boost pressure to 60 to 80 psi).This pump is suitable for RO systems rated up to 50GPD membrane.For RO systems, an increase in input pressure means an increase in water production and water purityRO systems will run more efficient, with less waste water. Since it uses a pressure switch and solenoid valve to turn on/off the water input, it can turn on and turn off more accurately than the mechanical auto shut-off valve.For large water containers or an open water tank, you can use a float switch or level switch to control the operation of the pump. Product Data Sheet: Aquatec.comWarranty Statement: Aquatec.comInstallation Instructions: Aquatec.com Aquatec’s original product, and still the “global standard” in booster pump technology, providing reliable inlet pressure for efficient membrane utilization.These pumps are capable of continuous duty and are effective for recirculation based applications as well. They are ideally suited to work with hydro-pneumatic storage systems but are compatible with most hydraulic shut-off valves also. These pumps are commonly used with one or more of Aquatec’s flow control components including: pressure switches (PSW Series), tank level controllers (TLC Series) or electronic shut-off valves (ESO Series). FAQ for RO BOOST PUMPS and DELIVERY PUMPS:Q. The R.O. system is not working properlyA. See IMI 147, R.O. Boost Pump Troubleshooting guide: Aquatec.comQ. The CDP, Continuous Duty Pump, runs continuously. A. See IMI 156, Automatic Shut Off Valve’s effect on the PSW’s shut off abilityQ. The pump that delivers water from the holding tank to the refrigerator is noisyA. The pressure switch controlled demand delivery pump is probably delivering morewater than the icemaker can accept (usually about 1/4 gpm at 35 psi), and is momentarilyreaching its shutoff pressure. Use a lower flow pump, and add an accumulator betweenthe pump and refrigerator if necessary. Open the “high voltage drinking water deliverypumps” selection chart, section A, for recommended choices. Q. What effect does feed pressure have on the tank/faucet pressures?A. None. The flow of water to the membrane will increase, but 80 psi pump dischargepressure will not change due to the preset by pass pressure.Q. What effect does higher by-pass pressures have on tank/faucet pressures?A. Since the pressure entering the membrane has increased, so will the pressure exitingthe membrane, at the expense of flow, however. Q. What is the membrane rating based on?A. Based on 95% rejection of TDS levels at 600 ppm and 60 psi membrane feed pressure,in a 70 degree F ambient environment. Q. The boost pump output pressure is only 60psi?A. Assuming you have not adjusted the by pass setting, you may be using a membranewith a permeate production higher than the pump can supply. Either switch to a higherflow pump, or go to a lower rated membrane. Q. Are low feed pressure shut off switches (LPS) available?A. The LPS comes with the appropriate wire harness, but a tee with a 1/8” NPT femalecenter port is not provided. TRANSFORMER Aquatec’s transformers are both current and temperature protected for additional safety protection. Aquatec pump-transformer combinations are designed to operate at maximum efficiency under a wide range of voltage conditions without overheating or overloading. This can save the end-user thousands of kilowatt hours per year compared to less efficient pumps. FeaturesNew Aquatec replacement tranformer for 6800 series booster pumpsDesigned and manufactured by Aquatec to ensure compatibility and proper operationStandard 2-Prong PlugOEM PartSpecificationsInput Voltage: 116-120 VACOutput Voltage Max: 24 VACCord Length: 6 FeetOverload Protection: Circuit Breaker, Auto-Reset Specification Sheet: Aquatec.com Copyright, 2009-2024; Discounted Water Filters, Inc, peponlinesales, and all affiliates; All Rights Reserved.
